Towing Capacity & Truck + Trailer Weight Calculator
Total your loaded trailer, estimate tongue weight and compare it with your tow rating, payload, GVWR, GCWR, rear GAWR and hitch limits.
- Free
- No sign-up
- Runs in your browser
Estimates only · data checked October 2026 · About this data
Estimates only. Your vehicle's door stickers, owner's manual, hitch label, trailer maker's guidance and actual scale weights always take priority. Never exceed any rating.
Your entries and saved results stay in this browser. No account, no tool cookies, nothing you enter is sent to a server.
Quick answer
A calculator for towing capacity compares your loaded trailer and truck load with every rating you enter, not just the tow rating. Add your door-sticker and manual numbers, the trailer, water, fuel and gear, and see which entered rating has the highest percentage utilization. Ratings that need a scale weight you have not entered are listed as not checked.
How to use the towing capacity calculator
- Enter the towing capacity for your exact configuration (engine, axle ratio, cab, bed, 2WD/4WD) from the owner’s manual or the maker’s towing guide. It is the only required rating.
- Add payload, GVWR and rear GAWR from the door-jamb stickers, and GCWR and curb weight from the manual. Leave unknown ratings blank (a 0 is rejected). A rating without the weights it needs is listed as Not checked, with the missing input named.
- Pick your hitch class, or type the rating printed on the hitch label, which overrides the class. The Class IV 10,000 lb value is for weight-distributing operation, so for Class IV either confirm that a weight-distributing hitch is in use or enter the label rating; otherwise the hitch is listed as Not checked.
- Choose the trailer type and enter its empty (dry) weight; for a boat trailer, add the boat’s dry weight and motor weight.
- Add trailer cargo and gallons of water, propane and fuel.
- Enter driver + passengers and truck cargo, hitch and accessories (bed and cab cargo, ball mount or fifth-wheel hitch, and add-ons not in curb weight).
- If you have truck scale weights, enter them; each replaces only its matching estimate.
- Press Check my setup. The table shows load, margin, percentage used and pass or over for each rating, and marks the one with the highest utilization.
How the calculator works: formulas and tongue weight
Following Nissan’s 2020 Towing Guide, gross vehicle weight (GVW) is the truck’s scale weight with passengers, cargo, fuel, hitch and tongue or king pin load, and it must not exceed GVWR. Gross combined weight (GCW) is the loaded truck plus the loaded trailer and must not exceed GCWR. The truck also needs payload left for the tongue load.
Tongue weight is part of the trailer that rests on the truck: it counts toward hitched GVW but only once in GCW. So the calculator separates the truck before and after hitching:
- Loaded trailer = empty weight + boat + motor + gear + water × 8.32 + propane × 4.11 + fuel × 6.47 (gasoline) or 7.05 (diesel), in lb per US gallon.
- Tongue weight = loaded trailer × tongue percentage.
- Truck before hitching = curb weight + driver and passengers + truck cargo, hitch hardware and accessories.
- Payload used = driver and passengers + truck cargo, hitch and accessories + tongue weight.
- Hitched GVW = truck before hitching + tongue weight.
- GCW = truck before hitching + loaded trailer (equivalently, hitched GVW − tongue weight + loaded trailer).
- Remaining towing capacity = tow rating − loaded trailer.
- Utilization of each rating = your load ÷ the rating × 100.
The results mark the entered rating with the highest utilization at your current weights. That is not always the first limit a heavier trailer would hit, because occupants and truck cargo are fixed while tongue weight grows by only 10–25% of added trailer weight. Example: a 2,000 lb tow rating, 1,500 lb payload, 1,000 lb of occupants and a 1,000 lb trailer use 76.7% of payload but 50.0% of the tow rating, yet a heavier trailer would hit the tow rating first.
Two published guidelines give slightly different tongue weight ranges; the calculator shows both and uses the upper Nissan value (15% conventional, 25% fifth wheel and gooseneck) for estimated payload and GVW. A measured tongue weight and your trailer manufacturer’s guidance take priority.
| Trailer type | Nissan 2020 Towing Guide | Dexter Axle LIT-008-00 |
|---|---|---|
| Conventional (bumper pull) | 10–15% | 10–14% |
| Fifth wheel / gooseneck | 15–25% | 15–20% |
Worked example: a truck rated to tow 6,500 lb pulls a 5,200 lb travel trailer. That uses 80.0% of the rating and leaves 1,300 lb. Tongue weight is 520 lb at 10% and 780 lb at 15%, and all of it counts against payload.
| Item | Value |
|---|---|
| Tow rating | 6,500 lb |
| Loaded trailer | 5,200 lb |
| Remaining towing capacity | 1,300 lb (80.0% used) |
| Tongue weight 10–15% | 520–780 lb |
GCW example: a 5,000 lb truck with 300 lb of driver and passengers and 200 lb of cargo and hitch weighs 5,500 lb before hitching. With a 5,000 lb trailer at 15% tongue weight, hitched GVW is 5,500 + 750 = 6,250 lb, and GCW is 5,500 + 5,000 = 10,500 lb, not 11,250 lb.
RV, boat and truck + trailer weight: what to count
As a towing calculator for RV setups, it catches the gap between dry and real weight. Fresh water weighs about 8.32 lb per gallon at 77 °F, so a 30-gallon tank adds roughly 250 lb. Liquid propane is about 4.11 lb per gallon; count the cylinders under gear. Fifth wheels put 15–25% of their weight on the truck under Nissan’s guideline, so watch payload and GVWR as closely as the tow rating.
As a boat trailer weight calculator, choose “Boat trailer” to add the boat’s dry weight, motor and fuel. EN 228 gasoline is 0.720–0.775 kg/L at 15 °C (about 6.01–6.47 lb per US gallon) and EN 590 diesel is 0.820–0.845 kg/L (about 6.84–7.05 lb/gal). The calculator uses the upper values, 6.47 and 7.05 lb/gal; fuel at other temperatures or specifications can differ.
As a truck and trailer weight load calculator, it totals occupants, truck cargo, hitch hardware and tongue weight against payload and GVWR, and adds the trailer to the pre-hitch truck weight for GCW. Each scale weight replaces only its own estimate:
- Hitched truck weight (steer + drive axles) replaces the estimated GVW.
- Total combination weight (all axles) replaces the estimated GCW.
- Hitched rear-axle weight is needed for the rear GAWR check.
- Loaded trailer weight replaces the trailer build-up.
- Payload stays an estimate, because it uses the percentage-based tongue load.
Looking for a trailer towing capacity chart by vehicle? Ratings vary within one model by engine, axle ratio, cab, bed length and drivetrain, and we have not compiled a verified chart. The calculator uses the numbers from your manual, the maker’s towing guide for your model year and your door stickers, the figures that apply to your truck.
| Hitch receiver class (SAE J684) | Max towing weight | Hitch system type | Typical use listed by USDOT |
|---|---|---|---|
| Class I | 2,000 lb | Weight carrying | Monocycle and jet ski trailers |
| Class II | 3,500 lb | Weight carrying | Small boat and utility trailers |
| Class III | 5,000 lb | Weight carrying | Medium travel and utility trailers, large boat trailers |
| Class IV | 10,000 lb | Weight distributing | Large travel and utility trailers, automotive trailers |
There are no federal motor vehicle safety standards for trailer hitches; many hitch makers use SAE J684 to classify and test them. In the USDOT table, Classes I–III are weight-carrying hitch systems and the Class IV 10,000 lb value is for weight-distributing operation. The calculator therefore applies 10,000 lb only when you confirm a weight-distributing setup; without that confirmation or a hitch-label rating, the hitch is listed as Not checked. It compares the loaded trailer with the hitch’s maximum towing weight only. The rating on your hitch label, for the way you actually tow, and its tongue-weight limit govern.
Methodology & sources
- Nissan USA, 2020 Nissan Towing Guide: weight rating definitions; tongue load 10–15%, king pin load 15–25%.
- Dexter Axle, Trailer Applications Manual LIT-008-00: hitch weight 10–14% and 15–20%; hitch class cross-check.
- Federal Register Vol. 65 No. 186, FR Doc 00-24584: hitch Class I–IV weights and hitch system types from SAE J684.
- Wikipedia, Properties of water: water density at 25 °C.
- Wikipedia, Diesel fuel: EN 590 and EN 228 density ranges.
- Wikipedia, Propane: liquid propane at 4.11 lb/US gal.
All weights are in pounds and US gallons. Fluid weights are computed from the cited densities (1 US gallon = 3.785411784 L, 1 lb = 0.45359237 kg). Payload is always estimated from the upper Nissan tongue percentage; GVW and GCW are measured or estimated depending on the scale weights you enter. Hitch class values are applied only to the hitch system type the source lists for them. Last updated: October 2026.
FAQ
How do I find my truck’s towing capacity?
Use the tow rating for your exact configuration from the owner’s manual or the manufacturer’s towing guide, and the GVWR, GAWR and payload from the door-jamb stickers. Ratings change with engine, axle ratio, cab, bed and drivetrain, so a generic number for the model is not enough.
How much tongue weight should my trailer have?
Nissan’s 2020 Towing Guide says 10–15% of actual trailer weight for conventional trailers and 15–25% king pin load for fifth wheel and gooseneck trailers. Dexter Axle’s applications manual gives 10–14% and 15–20%, so the ranges both sources agree on are 10–14% and 15–20%. A measured tongue weight and your trailer manufacturer’s guidance take priority over either range.
Why can payload run out before towing capacity?
Tongue or king pin weight rides on the truck and counts against payload together with the driver, passengers, truck cargo and hitch hardware. A heavy trailer can be under the tow rating while its tongue load pushes the truck over its payload or GVWR.
What are the hitch receiver class limits?
Per SAE J684 as tabulated by USDOT/NHTSA in the Federal Register (Sept. 25, 2000): Class I 2,000 lb, Class II 3,500 lb and Class III 5,000 lb maximum towing weight as weight-carrying hitch systems, and Class IV 10,000 lb for weight-distributing operation. The rating on your own hitch label governs for the way you actually tow.
How much do water, fuel and propane add to trailer weight?
This calculator uses 8.32 lb per gallon for water at 77 °F, 6.47 lb/gal for gasoline and 7.05 lb/gal for diesel (the upper EN 228 and EN 590 densities at 15 °C), and 4.11 lb/gal for liquid propane at 77 °F. A 30-gallon fresh-water tank alone adds about 250 lb.
Related guides
- Boat Trailer Winch Size Guide: Capacity by Boat Weight and Ramp Angle
- How to Load a Boat on a Trailer by Yourself Without a Spotter
- Bunk vs Roller Boat Trailer: Which Is Easier to Launch and Load?
- Trailer Leaf Spring Size Chart: Length, Eye Type and Capacity
- How Heavy Can a Trailer Be Without Brakes? State-by-State Weight Limits
- How to Replace a Boat Trailer Winch Strap Before It Snaps
More free tools
Ball Mount Drop and Rise Calculator
Enter receiver and coupler heights to calculate the required ball mount drop or rise in inches and millimeters.
Boat Trailer Parts Selector & Rating Checker
Enter your boat plus gear weight and the rating printed on each trailer part to see which parts are rated below your loaded weight.
Fifth Wheel / Gooseneck Pin Weight & Payload Checker
Estimate fifth wheel or gooseneck pin weight and check it, plus hitch, people and cargo, against your truck's door-jamb payload sticker.
