Trailer Light Wire Gauge Calculator
Find the minimum AWG wire for trailer lights, electric brakes, charge line or reverse circuits from current draw, run length and allowed voltage drop.
- Free
- No sign-up
- Runs in your browser
Estimates only · data checked October 2026 · About this data
Estimates only. Results check voltage drop for solid copper wire on a 12.0 V basis; they do not check ampacity, insulation, temperature or connectors. The 3%/10% limits are guidelines from the marine standard ABYC E-11, not an automotive rule. Follow your trailer, brake and vehicle manufacturers' instructions.
Your entries and saved results stay in this browser. No account, no tool cookies, nothing you enter is sent to a server.
Quick answer
What size wire for trailer lights depends on the circuit’s current and the round-trip wire length. Two 1157 bulbs on the bright filament plus four 194 markers draw 5.28 A; over a 25 ft run, 16 AWG keeps voltage drop under 10%, while 10 AWG is needed for 3%. Use the calculator for your exact circuit.
How to use the trailer light wire gauge calculator
- Pick the circuit. Size each circuit separately: tail/marker, one stop/turn side, electric brakes, the 12V charge line, or reverse/auxiliary.
- Enter the load. For lights, count the bulbs that are lit on that circuit at the same time. An 1157 has two filaments, so enter it under the bright filament for stop/turn and the dim filament for tail lights. For LED fixtures, add the current printed on the fixture label under “Other load”. For brakes, choose the magnet size and number of brakes.
- Enter the run length. Measure one way, from the tow vehicle connector to the farthest lamp or brake, in feet or meters. The calculator doubles it for the return path.
- Set the allowed voltage drop. The default is 3%. Raise it to 10% only for non-critical lighting.
- Optionally pick the gauge printed on your harness to see whether it keeps the drop within your limit.
The result shows the total circuit current, the minimum AWG size, the voltage drop at that size and a table comparing every gauge from 18 AWG to 4 AWG.
How the wire size is calculated
The method follows ABYC’s voltage drop explanation: voltage drop equals current times resistance (Vdrop = I × R). The circuit length is the conductor length from the positive source to the device and back to the negative source, so a 20 ft run counts as 40 ft of wire. Resistance comes from the standard solid copper table (ohms per 1,000 ft at 68 °F):
- Resistance (ohms) = ohms per 1,000 ft × (2 × one-way feet) ÷ 1,000
- Voltage drop (V) = circuit amps × resistance
- Drop (%) = voltage drop ÷ 12.0 V × 100
The calculator tries each gauge from thinnest to thickest and recommends the first one whose drop stays at or below your limit. Example: two 10 in. x 1 1/2 in. electric brakes draw 6.0 A (Dexter). Over a 20 ft run (40 ft round trip) with a 3% limit (0.36 V):
| Gauge | Ohms per 1,000 ft | Resistance, 40 ft | Drop at 6.0 A | Drop % |
|---|---|---|---|---|
| 14 AWG | 2.525 | 0.1010 Ω | 0.61 V | 5.05% |
| 12 AWG | 1.588 | 0.0635 Ω | 0.38 V | 3.18% |
| 10 AWG | 0.9989 | 0.0400 Ω | 0.24 V | 2.00% |
Bulb currents come from manufacturer ratings: 1157 at 2.10 A (bright filament) and 0.59 A (dim filament), 1156 at 2.10 A, and 194 at 0.27 A. LED fixtures vary too much by product to list, so enter the current from the fixture label.
Choosing a voltage drop limit, the ground wire and your existing harness
The marine wiring standard ABYC E-11 sets 3% as the maximum drop for critical circuits such as navigation lights and electronics, and 10% for other lighting. These figures are a guideline from the marine standard ABYC E-11, not an automotive rule. Many towing setups treat brakes and lights as critical, which is why 3% is the default here. ABYC also notes that a conductor must meet both its ampacity and its voltage-drop limit. This tool only checks voltage drop. Published ampacity tables for building wire in conduit do not apply to trailer wiring, so the tool does not show them. Confirm ampacity with your wire maker.
Ground wire. The white ground wire is the return path for every circuit at once. When brakes, stop lamps and running lights are all on, the ground carries their combined current. Add those currents and run the calculator with the total under “Other load” to size the ground. The tool models the return as a wire of the same length rather than a chassis ground, because there is no reliable data for chassis-return resistance.
Existing 4-pin or 7-pin harness. Harness gauges vary by maker, so check the AWG printed on the wire jacket and select it in the optional field. The calculator shows the drop for that gauge and flags it if it is too thin for your circuit. That is common on long trailers and on brake or charge circuits. Dexter lists insufficient wire size and poor connections among the common causes of low brake voltage, and it does not recommend fusing brakes.
Methodology & sources
- Wikipedia – American wire gauge: solid copper resistance per 1,000 ft at 68 °F, 18–4 AWG.
- ABYC – What Is Voltage Drop?: Vdrop = I × R, round-trip circuit length, ABYC E-11 3% and 10% categories.
- CEC Industries – 1157, 1156 and 194 lamp ratings.
- Dexter LD Service Manual, Magnet Amperes Chart, p. 21: 2.5 A per 7 in. magnet; 3.0 A per 10 in. and 12 in. magnet.
All drop percentages use a 12.0 V reference and solid copper at 68 °F. Warm wire and stranded cable have somewhat higher resistance, so leave some margin. Last updated: October 2026.
FAQ
What size wire do I need for trailer lights?
It depends on the circuit current and the round-trip wire length. For example, two 1157 bulbs on the bright filament plus four 194 markers draw 5.28 A; over a 25 ft run, 16 AWG keeps the voltage drop under 10%, but 10 AWG is needed to stay under 3%.
Why does the calculator double the wire length?
Current flows out on the positive wire and back on the return. Following ABYC’s definition, circuit length is the conductor length from the source to the device and back, so a 20 ft run is 40 ft of conductor.
Should I use 3% or 10% voltage drop?
The marine standard ABYC E-11 allows 3% for critical circuits such as navigation lights and 10% for other lighting. These are guidelines from the marine standard ABYC E-11, not an automotive rule; 3% is the safer default for brakes and lights.
How much current do electric trailer brakes draw?
Dexter’s magnet amperes chart lists 2.5 A per magnet for 7 in. x 1 1/4 in. brakes and 3.0 A per magnet for the 10 in. and 12 in. sizes, so two 10 in. brakes draw 6.0 A and four draw 12.0 A.
Does the ground wire need to be bigger?
The ground return carries the combined current of every circuit that is on at the same time, such as brakes, stop lamps and running lights together. Size it for that total current, not for a single circuit.
More free tools
Ball Mount Drop and Rise Calculator
Enter receiver and coupler heights to calculate the required ball mount drop or rise in inches and millimeters.
Boat Trailer Parts Selector & Rating Checker
Enter your boat plus gear weight and the rating printed on each trailer part to see which parts are rated below your loaded weight.
Fifth Wheel / Gooseneck Pin Weight & Payload Checker
Estimate fifth wheel or gooseneck pin weight and check it, plus hitch, people and cargo, against your truck's door-jamb payload sticker.
